因为井下装载机工作环境比较差，在使用过程中，一定要多加注意，正确的操作方法以及日常维护保养都是保证井下装载机可以正常工作的前提，当然，井下装载机使用时间久了，质量再好的设备，也不能完全避免一点不出故障，下面我们来谈一下井下装载机常见故障及方法！

Because the working environment of the underground loader is relatively poor, we must pay more attention in the process of use. Correct operation methods and daily maintenance are the premise to ensure that the underground loader can work normally. Of course, the underground loader has been used for a long time, and no matter how good the equipment is, it can not completely avoid failure. Let's talk about the common faults and solutions of the underground loader!

井下装载机出现故障的措施

Solutions to faults of underground loader

井下装载机驱动桥壳内润滑油不足，主、从动螺旋伞齿轮啮合空隙太小，差速器壳与十字轴行星齿轮空隙太大。加满润滑油按标准，调节其空隙达到正常值。

The lubricating oil in the drive axle housing of the underground loader is insufficient, the meshing gap between the driving and driven spiral bevel gears is too small, and the gap between the differential housing and the spider planetary gear is too large. Fill up the lubricating oil and adjust the clearance to the normal value according to the standard.

井下装载机转向泵进油滤清器或输油管阻塞，转弯转向柱与转向器连接处空隙小或无空隙，转向器阀芯与阀套、定子与转子配合过紧单稳阀或溢流调工作压力偏低或卡死，转向泵容量效率低。这时应该清洁过滤芯或拆换输油管，调节其空隙，拆换转向器或清洁碾磨，调节其工作压力达到标准值，拆换油泵。

The oil inlet filter or oil delivery pipe of the steering pump of the underground loader is blocked, the gap between the steering column and the steering gear is small or no gap, the cooperation between the valve core and the valve sleeve, the stator and the rotor of the steering gear is too tight, the working pressure of the monostable valve or overflow regulator is low or stuck, and the capacity efficiency of the steering pump is low. At this time, clean the filter element or remove and replace the oil delivery pipe, adjust its gap, remove and replace the steering gear or clean the grinding, adjust its working pressure to reach the standard value, and remove and replace the oil pump.

如果井下装载机轮边固锥滚子轴承出现毁坏，行星轮轴滚针轴承毁坏，太阳轮及行星轮断齿毁坏，内齿圈出现打齿，内齿圈与内齿圈支承架连接螺栓断。应当及时拆换轴承、调节其空隙，更换滚针轴承，更换行星轮以及太阳轮，拆换内齿圈，拆换其螺栓。

If the fixed tapered roller bearing at the wheel edge of the underground loader is damaged, the needle roller bearing of the planetary axle is damaged, the teeth of the sun gear and planetary gear are broken, the teeth of the inner gear ring are broken, and the connecting bolts between the inner gear ring and the inner gear ring support frame are broken. The bearing shall be replaced in time, the gap shall be adjusted, the needle roller bearing shall be replaced, the planetary gear and sun gear shall be replaced, the inner gear ring shall be replaced, and its bolts shall be replaced.

以上就是为大家介绍的有关井下装载机的详细介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.kuangjingjixie.com

The above is the detailed introduction of the underground loader. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.kuangjingjixie.com