The loader factory teaches you how to change the tire quickly

因为小铲车装载机常常行走于在比较恶劣的工地(例如岩层面)工作，夏季天气炎热，轮胎气压不均衡加上地面的难题，可能会致使发生爆胎状况，小型装叉车和大家聊聊如何更换轮胎。

Because small forklift loaders often walk on poor construction sites (such as rock layers), hot summer weather, uneven tire pressure and ground problems may lead to tire blowout. Small forklift loaders talk about how to replace tires.

(1)启动小型叉车设备，然后找到一个平坦开放的地方，按下动臂升降杆，使用动臂支撑将前轮胎与地面保持一定距离，然后在闪光桥附近的爆胎侧使用支撑，并将后轮胎楔入。

(1) First start the small forklift equipment, then find a flat and open place, press the boom lifting rod, use the boom support to keep the front tire at a certain distance from the ground, then use the support at the tire burst side near the flash bridge, and wedge the rear tire.

(2)利用撬杠等工具，拆装挡圈及锁圈随后查验轮胎衬垫与轮圈外表面是否黏连。如果发生这种情况，可以拆除支架，使设备在短距离内缓慢来回运行，直到衬垫与轮辋外表面脱落；禁止转弯和快速驾驶，以防止损坏内胎。随后，前胎再次支撑起来。

(2) Use crowbar and other tools to disassemble and assemble the retaining ring and lock ring, and then check whether the tire liner is adhered to the outer surface of the rim. If this happens, the support can be removed to make the equipment run back and forth slowly in a short distance until the pad and the outer surface of the rim fall off; It is prohibited to turn and drive fast to prevent damage to the inner tube. Then, the front tire is supported again.

(3)将内、外胎的相对位置做好标识，便于搜索、异物和修复电动装载机轮胎。

(3) The relative positions of the inner and outer tires shall be marked to facilitate the search, removal of foreign matters and repair of electric loader tires.

(4)用撬杠等工具从轮辋上拆下小叉车轮胎。注意，动作要柔和配合，默契，避免被轮胎撞，保护气门口。

(4) Remove the small forklift tire from the rim with a crowbar and other tools. Note that the action should be soft and cooperative to avoid being hit by tires and protect the air door.

(5)外胎被钢钉等细长异物刺伤后，如果表面无明显伤口或伤口小，可继续使用外胎（因为小叉车轮胎为低压轮胎，运行速度慢）；如果伤口较大，必须进行修复(因为设备运行时，轮胎会被挤压和摩擦，时间长了会损坏内胎，甚伤口越来越大，内胎突出，导致轮胎损坏。

(5) If there is no obvious wound or small wound on the surface after the outer tire is punctured by long and thin foreign bodies such as steel nails, continue to use the outer tire (because the small forklift tire is a low pressure tire and runs slowly); If the wound is large, it must be repaired (because the tire will be squeezed and rubbed when the equipment is running, and the inner tube will be damaged after a long time, or even the wound will become larger and larger, and the inner tube will protrude, leading to tire damage.

(6)如果是新内胎，必须拧紧阀口底部的螺栓，防止漏气；然后外胎内壁的异物，撒上适量的轻钙粉，擦拭均匀。为使衬垫与内、外胎紧贴，在装入内胎后应给内胎适度打气，再插入衬垫。

(6) If it is a new inner tube, the bolts at the bottom of the valve port must be tightened to prevent air leakage; Then remove the foreign matters on the inner wall of the outer tube, sprinkle an appropriate amount of light calcium powder, and wipe it evenly. In order to make the liner close to the inner and outer tubes, the inner tube shall be properly inflated after being installed, and then the liner shall be inserted.

(7)将轮胎放到轮圈上，安上锁圈、挡圈；安装过程中要保护好气门嘴。

(7) Put the tire on the rim and install the lock ring and retaining ring; Protect the air valve nozzle during installation.

(8)用车载空压机给轮胎打气。

(8) Use the on-board air compressor to inflate the tire.

(9)按下动臂升降杆，取出支架；到目前为止，更换六吨装载机轮胎需要大约50次min。

(9) Press the boom lifting lever and take out the bracket; Up to now, it takes about 50 times per minute to replace six ton loader tires.

以上就是为大家介绍的有关矿用装载机的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.kuangjingjixie.com

The above is a detailed introduction to the mining loader, and we hope it will be helpful to you. If you have any questions, please contact us. We will provide you with professional services http://www.kuangjingjixie.com