1 reverse the car to a good position

装载机装车之前，注意观察将翻斗车倒到工作区的佳位置，既能节省时间也能提高很多效率。

Before loading the loader, pay attention to observe that the tipper is placed in a good position in the working area, which can not only save time but also improve a lot of efficiency.

2装载有计划

2 loading plan

装载机装载前应先想好装载顺序，尽量把都靠近车厢前面，因为这样装起来快封顶的时候不会说前面少了半铲，装载机装载时要有计划。

Before loading, the loader should first think about the loading sequence, and try to put them all close to the front of the carriage, because it will not say that the front is less than half a shovel when the loader is loaded and the loader should have a plan when loading.

3物料快满时将高出的部分推平

3. When the material is almost full, push the higher part flat

快满了的时候可将物料慢慢的推过去，尽量使物料推到较少的一边，因为实际装载时，装载机升不到那么高。如果还差一铲就装后面，因为你一次性前面装的太满了封顶的时候会很不方便。

When it is almost full, the materials can be pushed slowly to the side with less materials as far as possible, because the loader cannot rise so high during actual loading. If you still need a shovel to install it in the back, it will be very inconvenient when the front is too full at one time.

4掌握时间差

4 master time difference

装载机装车时主要就是个时间差的掌握，铲料时，右手要勤快，当车子阻力大了不动时，要多操纵动臂摇臂，不要阻力一大就猛加油门，那样既浪费燃油又伤车，还不能提高工作效率。

When loading the loader, it is mainly a matter of time difference. When shoveling the material, the right hand should be diligent. When the vehicle resistance is large and does not move, it is necessary to operate the boom rocker arm more. Do not suddenly increase the throttle as soon as the resistance is large, which will not only waste fuel and hurt the vehicle, but also not improve the work efficiency.

5注意要做组合动作

5 pay attention to the combination action

铲入：行走（前冲）、放大臂、放平斗同时做，即走到料堆前时，你的铲斗也应正好放到位，可以借着冲劲铲入；

Shovel in: walking (forward punching), magnifying arm and leveling bucket shall be carried out at the same time, that is, when walking in front of the pile, your bucket shall also be placed in the right position, and you can shovel in with momentum;

翻斗、提臂和倒车同时做，边倒车边缓慢提大臂、摆正铲斗，倒正换前进档后，继续边走边提大臂；

Tipping, arm lifting and reversing shall be carried out at the same time. The boom shall be slowly lifted and the bucket shall be straightened while reversing the vehicle. After reversing and shifting to the forward gear, the boom shall be lifted while walking;

卸料：走到离车箱不远时就要开始翻斗卸料，不用担心物料倒出来，因为动作如果足够快的话，物料会由于惯性的作用迟滞一下才会开始滑落，不会立马下来的，待铲斗达到车箱边缘内后，在继续翻斗的同时，还要同时降一些大臂，到合适的位置后，使铲斗正好翻到位，也停止降大臂，同时再点一下刹车，物料会因惯性的冲劲迅速滑落的，总之不要停顿一秒的时间。

Unloading: when you are not far from the trunk, you should start to dump the material by tipping the bucket. Don't worry about the material pouring out, because if the action is fast enough, the material will start to slide due to the inertia and won't come down immediately. After the bucket reaches the edge of the trunk, you should also lower some boom at the same time while continuing to dump the bucket. When it reaches the appropriate position, make the bucket just turn in place and stop lowering the boom, At the same time, click the brake again, and the material will quickly fall due to the momentum of inertia. In short, do not stop for a second.

本文的精彩内容由井下装载机提供知识提供，本网站还有很多的精彩内容，更多的内容您可以点击进入：http://www.kuangjingjixie.com我们有专门的客服为您解答问题

The wonderful contents of this article are provided by the knowledge provided by the underground loader. There are many wonderful contents on this website. You can click to enter more contents: http://www.kuangjingjixie.com We have special customer service to answer your questions